LANMU Replacement Tires Compatible with IRobot Roomba 500, 600, 700, 800, 900, E5, E6, i7 Series Vacuum, Front Caster Wheel Assembly (2 Pack Tires+1 Front Caster Wheel)

The old tires were harder to get off than I thought. They had spots of glue and points that stuck into the wheel, I had to cut each one off. Because I had followed the direction and removed the wheel assemblies from the vacuum, reinstalling the new wheels was simple. When the job was done the new tires fit perfect and work perfect, just a little harder than I had hoped.

Changing these out on an S9 is no easy task. Once you get them changes don’t forget to remap because these things are pretty beefy and at least for me on the carpeted floor the robot was getting lost.To change on an S9 you need to remove the dust bin, flip over and remove the vacuum beater assembly, remove the cover behind the beaters, disconnect the battery, can’t remember if any screws hold the wheel assembly in but for one you need to fold the cliff eye up and for both you have to push the release for the wheel assembly on the inside of the dust bin compartment. Once the wheel assembly is out the pain begins. On the S9 not only is the tread glued on but it is also pined in. I had to remove the spring that holds the wheel down by taking the one screw out of the plastic shield on the motor. Don’t let the spring fly!! Then I had to walk the tread on in a way that didn’t damage anything. This is a very tight squeeze and could easily break something. I don’t recommend doing this or using this product unless you are extremely mechanically inclined. Once you start to take the old tread off you are at the point of no return.

Good value item vs stock I ROBOT wheel module replacement. Front pivot wheel direct replacement for I ROBOT 655, no issues. Removing the worn out rubber drive tires is a chore if you have not replaced them before. Mine were well worn and required a utility knife, flat head screw driver and pliers to remove. As others have stated on YouTube videos, there is a layer of OEM glue and nubs that hold the tire on the wheel surface. As part of the installation, I found that I needed to go back and scrape off the glue on the wheel surface as it caused the replacement tire to ride too high making the rotation very rough inside the wheel fender. After scraping off old glue the replacement tire pressed into the wheel groove much better and allowed adequate rotation within the wheel fender. Over all this set is a good value but required some manual labor to remove old rubber tires. If my 655 lasts through this set of tires I will probably save the time and effort and buy the OEM I ROBOT wheel assembly. But if you like to tinker, go for it buy this set!

Bood materials and fit. Everything ok so far.About tires, it could have instructions, since the installation is not straighforward: you need to peel old tires (not so easy) and replace using some sort of good glue (at least it was my guess, if not new tires could slip agains wheel, because they have no support to stay in place besides its own friction).

After 3 years, the tires on my 960 were bald. It would slip and get stuck because it didn't have the traction to move on. Put these on and it's like new again!You will have to remove the bottom plate and both drive wheel assemblies, but there are only a few screws holding each on and it's very easy to do. Once you have them out, the old tires have to be pried off the wheel - there are nubs that secure the old ones to the wheel that you either have to pull apart or cut. Don't worry about trying to completely remove the remnants of the nubs from the holes - just make sure you trim them flush with the wheel.The new ones simply slip over the wheels and you're done! Took me less than 10 minutes for both, and that includes the time it took to watch a video to make sure I wasn't damaging anything.The front wheel just pops into place - easy stuff.Great way to refresh your Roomba and give it the traction it needs!

Perfect fit for iRobot, saved a lot of money and works well.

This fit my Roomba s9+. They were EXTREMELY hard to get on and took almost an hour to do. They seem noisier than the original but they do work pretty well. My biggest fuss is that they slid off all the time and I have to readjust them often. The tread is very thick so I think they will last awhile.

Getting the old tires off was the hardest part as at first I didn't realize the original tires also had rubber studs that went into the wheel to really hold the tires on, once I figured that out a sharp knife to cut them off flush to the wheel worked. New tires went on, fitted just right and now roomba is off again. Original tires lasted 10 years. Nice touch was having a new front roller wheel and a new spinner brush included which I also put on. So far very happy.

A perfect fit for our 960! Ours is 2.5 years old and is used daily. As you can see, the tire treads were completely gone -- to the point it couldn't climb low-pile area rugs or even reliably dock the charging station.We popped off the cover, replaced the wheels, gave it a good blow-out, and it's riding around like new!

Quedaron a la perfección en mi Roomba