LinksysVelop Mesh Home WiFi System, 4,500 Sq. ft Coverage, 30+ Devices, Speeds up to (AC1300) 1.3Gbps - WHW0103

These help with the WIFI dead spots in our home. My daughter had a hard time in her room with connections and this solved that problem. They were a little tricky to set up but I watched some YouTube and googled some answers and finally got it done

I’ve been using this system for about a month now and it’s been running very well (aside from some modifying my setup – luckily for most people noting too technical). My speeds have gone up from when I had a 4 year old LinkSys Wi-Fi router (middle of the road, $200-$250 model at the time) from about 15-18MbpS to about 30-35MbpS (we’re paying for 50MbpS – fastest available in my neck of the woods).The largest plus is that you only have to wire one unit (your primary) to your modem. The others just need a Wi-Fi signal and act as good signal boosters. Installation is easy, too. Install the app and log in, connect the primary to your modem, plug it in and turn it on then follow the prompts in the app – this process takes about 30 minutes. Adding additional nodes is very easy, plug it in, turn it on, then add the device in the app, this takes about 10-15 minutes (most of the time is waiting for it to boot up and self-configure).Each node also has 2 RJ-45 ports to wire a device (your primary will only have one available, though). Plan ahead with any devices that may need a wired connection.I think my home is larger than the average home and we will be good with 4 (and it’s a little oddly set up). I think the average home will need 2-3 – but my suggestion below will help you see how many you’ll need).I do have some suggestions, though:First, plan ahead. Get an app that measures Wi-Fi signals (I use Netgear’s Wi-Fi Analytics – but that’s only available for Android) and measure your signal around the house (maybe even draw a map and your measurements). I wouldn’t recommend putting a node anywhere you get a signal lower than -65 dBm (we’re dealing with negatives, so -80 is worse or weaker, -60 is better or stronger). If your initial measurements show an area (or more) that is less than -70 dBm then remeasure after putting your nodes in. Install your primary then take measurements to see where they should go, using your map as a guide for weak signals (don’t worry if areas show a weaker signal, this can be normal).Don’t be afraid to move the nodes, once they’re connected to your network you won’t need to re-add them.Second, allow them room to breathe. Don’t put then in an enclosed area, they can overheat and can result in loss of connectivity (I had this issue – one didn’t have ventilation and was losing its signal constantly, I moved it just a few feet to an open area and it’s been a lot better).Third, and this is just good networking practice, set any network printers to a static IP (or, preferably a reservation in the network). This will help with some stability in the long run.Fourth, run the firmware updates as soon as you have your network set up. This is another good practice.Their mobile app is good but missing some features that their old management software had (like usage by device). Hopefully LyynkSys will update it.(Note: I did not rate their tech support because I did not contact them).

Update; 8/4/2020Still just as good as my 2 previous updates. However, for last few weeks I’ve been experiencing the WiFi goin out approx 2-3 x a day. I’m leaning more towards the cable modem is causing it. I’ve been on the phone with cust service both with Linksys as well as Optimum who is my provider. I believe they are goin fiber optic soon and have a bad feeling that I’m in for some really bad issues....I’ll keep ya posted.Update : 5/16/2020:Still kicks butt, by far BEST WIFI IVE HAD...My older Linksys WiFi Router, (and extender) which I’d say was approx 2-3 yrs old had just gotten progressively slower over the past few months, due to 5 iPhones in my house, 2 laptops, 2 Mac PC’s, wireless printer, Xbox 1, Xbox 360, Play Station 2, 3, 4, etc. I could no longer stand my kids screaming the Wi-Fi sucks. etc etc...lol.ANYWAY, I had had enough & spoke to a buddy of mine who’s really into this “stuff” so to say, and he has about the same amount of wireless devices at his home as well. He did all the research,..( hee hee hee, not me..) and he purchased the same router and told me to get “this one”. Like I said, it’s only been a week, but so far so good. All is well with the kids now..!!..lol...They are soooo happy that I finally got around to buying a new router. There gaming is working fine, as it’s supposed to, our iPads & phones are also working as they should.I will update this review in another few weeks (...IF SOMEONE COULD REMIND ME..!!..).I feel very confident that the review will stay positive.*** UPDATE 11/4/19 ***STILL the best WiFi I ever had. Works perfectly. Had to contact cust.service for a minor issue and the rep was extremely helpful & had the issue fixed in no time...!!....would DEF recommend...!!....AAA+++